Turn on the heat when someone gets home
Other popular Heatmiser workflows and automations
-
1
-
-
Arriving Home - Lights On
3
-
-
Sonoff Thermostat heating switch
-
-
If there's a calendar event tomorrow, run a recipe
-
-
Set the Temperature on a Heatmiser Thermostat when Apilio triggers and action
-
-
If Window/Door opened, place heating zone into Standby mode.
-
-
Door/Window Closed - Re-Enable Heating
-
-
Door/Window Open - Heating Off
1
-
-
Cancel Standby Mode on the selected Heatmiser Thermostat when Apilio triggers and action
-
Build your own Heatmiser and LightwaveRF Power automations
Triggers (If this)
-
Temperature rises above
This Trigger fires every time the temperature rises above a threshold you specify.
-
Socket switched on
This trigger fires whenever a socket is turned on.
-
Temperature drops below
This Trigger fires every time the temperature drops above a threshold you specify.
-
Socket switched off
This trigger fires whenever a socket is turned off.
-
neoHub Away Mode
This trigger fires when your neoHub is set to away mode.
-
neoHub Home Mode
Triggers when your neoHub returns to Home Mode.
-
Low Battery
This trigger fires when your Heatmiser Device has a Low Battery.
-
Contact Sensor Closed
This trigger fires when the Contact Sensor is closed
-
Contact Sensor Open
This trigger fires when the Contact Sensor is opened
Temperature rises above
This Trigger fires every time the temperature rises above a threshold you specify.
Socket switched on
This trigger fires whenever a socket is turned on.
Temperature drops below
This Trigger fires every time the temperature drops above a threshold you specify.
Socket switched off
This trigger fires whenever a socket is turned off.
neoHub Away Mode
This trigger fires when your neoHub is set to away mode.
neoHub Home Mode
Triggers when your neoHub returns to Home Mode.
Low Battery
This trigger fires when your Heatmiser Device has a Low Battery.
Contact Sensor Closed
This trigger fires when the Contact Sensor is closed
Contact Sensor Open
This trigger fires when the Contact Sensor is opened
Actions (Then that)
-
Cancel temperature hold
This Action will cancel a temperature hold on the selected Heatmiser Thermostat.
-
Switch on a socket
This Action will switch on your socket.
-
Set temperature hold
This Action will enable a temperature hold on the selected Heatmiser Thermostat.
-
Switch off a socket
This Action will switch off a socket.
-
Turn neoPlug on
This Action will allow you to switch on the selected neoPlug.
-
Lock device
This Action will lock a device, preventing use of the physical buttons on the device.
-
Turn neoPlug off
This Action will turn off the selected neoPlug.
-
Unlock a device
This Action will unlock a device, allowing use of the physical buttons on the device.
-
Set Temperature
The Action will set the temperature on the selected Heatmiser Thermostat.
-
Fully lock a device
This Action will fully lock a device, preventing both the use of physical buttons and radio control of the device.
-
Boost Timer
This Action will activate a Timer Boost on the selected Heatmiser Timer.
-
Open a relay
This Action will open a relay.
-
Set Away Mode
This Action will activate Away Mode on your neoHub
-
Close a relay
This Action will close a relay.
-
Set Home Mode
The Action will activate Home Mode on your neoHub.
-
Stop a relay
This Action will stop a relay.
-
Set Standby Mode
This Action will activate Standby Mode on the selected Heatmiser Thermostat.
-
Cancel Standby Mode
This Action will cancel Standby Mode on the selected Heatmiser Thermostat.
-
Run Profile
This action will send a stored profile to the selected thermostat.
-
Run recipe
This action will run a Heatmiser Neo recipe.
Cancel temperature hold
This Action will cancel a temperature hold on the selected Heatmiser Thermostat.
Switch on a socket
This Action will switch on your socket.
Set temperature hold
This Action will enable a temperature hold on the selected Heatmiser Thermostat.
Switch off a socket
This Action will switch off a socket.
Turn neoPlug on
This Action will allow you to switch on the selected neoPlug.
Lock device
This Action will lock a device, preventing use of the physical buttons on the device.
Turn neoPlug off
This Action will turn off the selected neoPlug.
Unlock a device
This Action will unlock a device, allowing use of the physical buttons on the device.
Set Temperature
The Action will set the temperature on the selected Heatmiser Thermostat.
Fully lock a device
This Action will fully lock a device, preventing both the use of physical buttons and radio control of the device.
Boost Timer
This Action will activate a Timer Boost on the selected Heatmiser Timer.
Open a relay
This Action will open a relay.
Set Away Mode
This Action will activate Away Mode on your neoHub
Close a relay
This Action will close a relay.
Set Home Mode
The Action will activate Home Mode on your neoHub.
Stop a relay
This Action will stop a relay.
Set Standby Mode
This Action will activate Standby Mode on the selected Heatmiser Thermostat.
Cancel Standby Mode
This Action will cancel Standby Mode on the selected Heatmiser Thermostat.
Run Profile
This action will send a stored profile to the selected thermostat.
Run recipe
This action will run a Heatmiser Neo recipe.
How to connect Heatmiser and LightwaveRF Power
Find or create an Applet
Start by discovering an automation to connect or customizing your own. It's quick and easy.Connect IFTTT to your accounts
Securely connect your Heatmiser and LightwaveRF Power accounts.Finalize and customize your Applet
Review your trigger and action settings. Your Applet is ready to go!
IFTTT helps all your apps and devices work better together