This Trigger fires when specified motion sensor tag(s) armed in motion detection mode, have moved.

This trigger fires when the device is turned on/off

This Trigger fires when a specified motion sensor tag(s) or reed sensor(s) detect that a door or window is open.

This trigger fires when the sensor is armed or disarmed

This Trigger fires when a specified motion sensor tag(s) or reed sensor(s) detect that a door or window is closed.

This trigger fires when contact sensor triggered

This Trigger fires when specified PIR KumoSensor detects movement.

This trigger fires when motion sensor triggered

This Trigger fires when specified PIR KumoSensor or regular motion sensor tag detects no movement for a time-out period.

This trigger fires when water leakage is detected or stops

This Trigger fires when a specified tag senses that its ambient temperature exceeds an upper threshold configured at temperature options screen inside the WirelessTag app.

This trigger fires when battery is low

This Trigger fires when a specified tag senses that its ambient temperature falls below an lower threshold configured at temperature options screen inside the WirelessTag app.

This trigger fires when the alert is triggered

This Trigger fires when a specified tag senses that its ambient temperature returns between the upper and lower thresholds configured at temperature options screen inside the WirelessTag app.

This trigger fires when the gateway sub device is triggered

This Trigger fires when a specified tag with humidity or moisture monitoring enabled, detects "too wet" state. Adjust the threshold from the humidity/moisture options screen inside the WirelessTag app.

This Trigger fires when a specified tag with humidity or moisture monitoring enabled, detects "too dry" state. Adjust the threshold from the humidity/moisture options screen inside the WirelessTag app.

This Trigger fires when a specified tag with humidity or moisture monitoring enabled, returns within normal humidity range. Adjust the upper/lower thresholds from the humidity/moisture options screen inside the WirelessTag app.

This Trigger fires when specified water sensor tag detects water with its resistive sensor, or when you short circuit its tip.

This trigger fires when specified water sensor tag transitions from detected water state to not detected water state, or when you open circuit its tip.

This Trigger fires when a specified tag goes out of range. Note that the system can only determine whether a tag is out of range, if the "auto-update" is enabled.

This Trigger fires when a specified tag comes out of "out of range" state. Only tags with auto-update is enabled can come out of "out of range" state.

This Trigger fires when the server detects that specified tag manager lost Internet connection due to power outage or Internet connection problems.

This Trigger fires when specified tag manager is back online.

This Trigger fires every time a specific KumoApp produces a log message with KumoApp.Log call with a specific type.

This Trigger fires every time a temperature/humidity/lux update is received from specified sensor/tag(s).

This Trigger fires when a specified tag senses that its ambient light exceeds an upper threshold configured at light options screen inside the WirelessTag app. For example, this can be used to detect fridge door open.

This Trigger fires when a specified tag senses that its ambient light exceeds an lower threshold configured at light options screen inside the WirelessTag app. For example, this can be used to turn on a light in a room.

This Trigger fires when a specified tag senses that its ambient light intensity returns between the upper and lower thresholds configured at light options screen inside the WirelessTag app.

This query returns a list of when the specified tag sensed that its ambient temperature had returned between the upper and lower thresholds configured on the temperature options screen inside the WirelessTag app. Note: this query will only return future e

server health check ping

The query returns if the specified tag manager is online or offline, as well as how many hours it has been online.

This query returns specified door/window sensor/tag's current state, including temperature, humidity/lux (when available) and motion state such as door open/close, moved, or detected motion (for PIR sensor)

This query returns a list of when the server detects that specified tag manager lost Internet connection due to power outage or Internet connection problems.

This query returns a list of when a specified tag sensed that its ambient temperature fell below a threshold. Note: this query will only return future events after this Applet is created.

This query returns a list of times when a specified tag senses that its ambient temperature exceeded an upper threshold configured at temperature options screen inside the WirelessTag app. Note: this query will only return future events after this Applet

This query returns a list of when a specified tag with humidity or moisture monitoring enabled, detects "too wet" state.

This query returns a list of when the specified tag manager was back online.

This query returns a list of when specified water sensor tag transitions from detected water state to not detected water state, or when you open circuit its tip.

This query returns a list of when specified motion sensor tag(s) armed in motion detection mode, have moved.

This query returns a list of when a specified tag goes out of range. Note that the system can only determine whether a tag was out of range, if the "auto-update" was enabled.

This query returns a list of when specified PIR KumoSensor or regular motion sensor tag detects no movement for a time-out period.

This query returns a list of when a temperature/humidity/lux update was received from specified sensor/tag(s).

This query returns a list of when a specified motion sensor tag(s) or reed sensor(s) detect that a door or window was open.

This query returns a list of when a specified tag senses that its ambient light exceeds an upper threshold configured at light options screen inside the WirelessTag app. Note: this query will only return future events after this Applet is created.

This query returns a list of when a specified motion sensor tag(s) or reed sensor(s) detect that a door or window was closed.

This query returns a list of every time a specific KumoApp produces a log message with KumoApp.Log call with a specific type.

This Action will beep the tag. NOTE: Only compatible with the Motion Sensor Tags with buzzer.

This action will set the device (not including lights) to a specified mode.

This Action will stop the tag beeping. This action can also be used to test tag connectivity.

You can choose to arm or disarm your device through this action.

This Action will turn on LED on the tag or a WeMo device.

This action will turn on/off the device of your choosing.

This Action will turn off LED on the tag or a WeMo device.

This action will turn on/off the Night Light of your choosing.

This Action arms motion sensor on a tag. Regular angle based motion sensor, Reed KumoSensor and PIR KumoSensor can all be armed using this action.

This action will set the device Volume

This Action disarms motion sensor on a tag. Regular angle based motion sensor, Reed KumoSensor and PIR KumoSensor can all be disarmed using this action.

This action will set the light to specified color.

This Action will enable temperature monitoring on a tag.

This action will set the light to a specified brightness.

This Action will disable temperature monitoring on a tag.

This action will turn on/off the warm mist of the device you've chosen.

This Action will enable humidity or moisture monitoring on a tag. NOTE: Only compatible with Tags with humidity or moisture sensor.

This action will turn on/off the oscillation of the device you've chosen.

This Action will disable humidity or moisture monitoring on a tag.

This action will turn on/off the white noise of the device you've chosen.

This Action will start a KumoApp installed under the current user account. If the KumoApp is running, nothing will happen. If a KumoApp does not register any event handler or timer, it will automatically stop after executing the first time, allowing this action to run multiple times without user intervention.

This action will turn on/off the Dreamview of your choosing.

This Action will stop a KumoApp. If the KumoApp is not running, nothing will happen.

This action will apply the snapshot of your choice to the device that created the snapshot

This Action will enable brightness/ambient light intensity monitoring on a tag. NOTE: Only compatible with Tags with ambient light sensor.

This action will apply the Smart Aroma Diffuser Scene of your choice to the device

This Action will disable brightness/ambient light intensity monitoring on a tag.

This action will force an update to read the current temperature, humidity and ambient light (when available).